Piles are basically load bearing building elements that are used to primarily transmit structural loads through the soil. Piles are majorly used to provide support to buildings located in areas that have poor soils. It basically consists of piles which can be made of timber, steel or concrete. The piles are then driven deep in to the ground till they reach the bedrock. This is worth knowing about marine pile drivers.
A bedrock is described as a hard soil layer situated deep in the ground. At bedrock, the piles cannot be driven any more therefore providing stability to structures above. There are two major varieties and include, friction piles and end bearing piles. When the load is transmitted to the soil via skin friction between the soil and surface of the pile, friction piles becomes necessary.
End bearing piles are used when the load is transmitted into the soil through the lower tip. Many piles depend on the combination of friction and end bearing for their supporting strengths. They may be classified of the basis of either their use or from the materials from which they are made. Selecting proper piles to use is very important and the selection should be done carefully.
Choosing the type of piles to use is the duty of the contracted engineer. This means that the engineer must pick piles which are best suited to particular job. While doing this they must also figure in factors affecting performance and installation. Many consideration factors affect the selection decision. Weight of the structure to be supported and size are examples of factors to be considered.
Structures vary from a residential, commercial building, a simple structure like water tanks. What matters is the physical property of the soil. The presence of material for piles and the quantity of piles needed so as to have the structure supported. It is also vital to examine the depth required for piles to be laid so as to support the structure.
This is helpful in determining the type of pile driver to be used. Pile drivers are basically devices used to drive piles underground. Determining the type of load driver requires several investigations to be undertaken. Such investigations include site studies, geotechnical study and a basic penetration test should be done. Another very important test is the load test this is done to be able to establish the total amount of load to be carried by the pile.
When piles are driven underground the force that is used to support then is the same force that causes resistance to piles as they are being driven underground. In order to deal with this this is where the drivers come in. They help furnish the energy required to drive the piles underground.
Pile hammers are some of the load drivers that are used in most cases to drive piles underground. To mention, they include diesel hammers and vibratory hammers. Diesel hammers cause explosion and compression energy to the piles while vibratory hammers uses exciting shafts rotating in an opposite direction to move piles underneath the ground.
A bedrock is described as a hard soil layer situated deep in the ground. At bedrock, the piles cannot be driven any more therefore providing stability to structures above. There are two major varieties and include, friction piles and end bearing piles. When the load is transmitted to the soil via skin friction between the soil and surface of the pile, friction piles becomes necessary.
End bearing piles are used when the load is transmitted into the soil through the lower tip. Many piles depend on the combination of friction and end bearing for their supporting strengths. They may be classified of the basis of either their use or from the materials from which they are made. Selecting proper piles to use is very important and the selection should be done carefully.
Choosing the type of piles to use is the duty of the contracted engineer. This means that the engineer must pick piles which are best suited to particular job. While doing this they must also figure in factors affecting performance and installation. Many consideration factors affect the selection decision. Weight of the structure to be supported and size are examples of factors to be considered.
Structures vary from a residential, commercial building, a simple structure like water tanks. What matters is the physical property of the soil. The presence of material for piles and the quantity of piles needed so as to have the structure supported. It is also vital to examine the depth required for piles to be laid so as to support the structure.
This is helpful in determining the type of pile driver to be used. Pile drivers are basically devices used to drive piles underground. Determining the type of load driver requires several investigations to be undertaken. Such investigations include site studies, geotechnical study and a basic penetration test should be done. Another very important test is the load test this is done to be able to establish the total amount of load to be carried by the pile.
When piles are driven underground the force that is used to support then is the same force that causes resistance to piles as they are being driven underground. In order to deal with this this is where the drivers come in. They help furnish the energy required to drive the piles underground.
Pile hammers are some of the load drivers that are used in most cases to drive piles underground. To mention, they include diesel hammers and vibratory hammers. Diesel hammers cause explosion and compression energy to the piles while vibratory hammers uses exciting shafts rotating in an opposite direction to move piles underneath the ground.
About the Author:
Get fantastic pile driver purchase tips, today. You can also get more information about state-of-the-art marine pile drivers at http://www.piledriver.org right now.